1995-2004 Tacoma Rear Bumper

You are here

Marlin Crawler Rear 1st gen Tacoma Tube BumperMarlin Crawler Rear 1st gen Tacoma Tube Bumper 2Marlin Crawler Rear 1st gen Tacoma Tube Bumper 3Marlin Crawler Rear 1st gen Tacoma Tube Bumper 4Marlin Crawler Rear 1st gen Tacoma Tube Bumper 5Marlin Crawler Rear 1st gen Tacoma Tube Bumper 6Marlin Crawler Rear 1st gen Tacoma Tube Bumper 7Marlin Crawler Rear 1st gen Tacoma Tube Bumper 8

Check-out with Paypal Credit
for six no-intrest payments!

Rocks are hard. Fight back with with our tough American-made USA steel rear bumpers.

This is our rear bumper designed to fit 1995-2004 1st generation Tacomas, and is built by our heavy duty metalwork subsidiary Locktup4x4 & Fabrication to fit your specific vehicle. Made from 1-3/4" round .120 USA tubing and designed with a 4-bolt frame mount system with side bracing. This 1st gen Tacoma bumper features a heavy duty double-tubed rear crossmember. The end result is a rigid bumper that can easily bear the load of your truck with a Hi-lift jack or anchor point anywhere along it's main tube while also having a low profile ideal for Rock Crawling.

A Marlin Crawler heavy duty metalwork company

Key Features:
  • Oversized D-Ring Shackle Hangers on both sides, our most robust design ever!
  • Locktup4x4 Roadrunner step plate
  • We've brought back our classic corner protection vertical uprights that extend protection as much as possible while still allowing the tailgate to function
    • This is our original design that was custom built for The Crawler Truck 18-years ago!
  • Two intermediate support beams for increased rear impact strength
  • Enlarged receiver hitch rear bracket for adding additional towing support beams
  • Integrated Side Frame Supports included at NO additional charge on all Rear Bumpers!
    • Connects both side wrap-around protection to the frame for maximum strength
    • Able to lift the vehicle with a Hi-Lift jack from any point, rear or side of the bumper
  • Increased Side Protection Length
    • Now closer to the rear tire for maximum body protection!

Our unique receiver design does not interfere with the stock spare tire location nor the tailgate, which was a challenge since we use heavy duty D.O.T.-recommended seamless square 2.5" x 1/4"-wall receiver tubing. Watch out for other bumper manufactures who cut corners by welding multiple separate pieces to "build" receivers not in accordance to government transportation safety laws.

They are shipped unpainted. We recommend using Restoleum spray paint or powdercoat to give it a lasting finish. Also, for most applications, two small body notches are required on the bed skirt below the tail gate hinges to clear our sturdy 1/4" thick integrated frame mount rails.

These bumpers are well made and could in theory tow a variety of trailers well, however, they are not rated and we do not have any weight or tongue loading information. This is a well made Rock Crawler bumper that also happens to be a very nice full daily driver replacement bumper.

Proposition 65 Warning for California Consumers

WARNING: Products we sell can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.

Related Products

NEW: In preparation to manufacture 2005+ Tacoma front & rear tube bumpers, we have
switched all our bumpers over to the strongest and most dent-resistent USA DOM tubing!

Shown: 2016+ 3rd gen Tacoma low profile Rock Crawling Tube Bumper, Prototype No.01

1979-95 Shortbed Pickup and 4Runner Rear Bumper Pictures

NEW: All Rear Bumpers now feature our Locktup4x4 "Roadrunner" Step Plate!

Pictures from Dusy/Ershim, Rubicon, and Moab!

Recommended Small Frame Weld

Check out our comparison tech article of our USA steel strength!

1995-2004 1st-gen Tacoma Rear Bumper

Note: We are now producing these through our heavy duty metalworks subsidiary Locktup4x4 & Fabrication and will be featuring our Locktup4x4 Roadrunner logo on the step plate.

Recommended Small Frame Weld